replaced MC, litle soft.
#1
Senior Member
Thread Starter
Join Date: Mar 2011
Location: Norway
Posts: 651
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1993
Model: Grand Cherokee
Engine: 4.0L I6
replaced MC, litle soft.
This weekend i replaced the break MC and both front calipers, dust shield and hub bolts. I have ABS but i only bleeded it manualy, do i need to cycle/run the ABS pump, i replaced the calipers first and bleeded them, so the ABS pump hasnt been empty. When replacing the MC i bleeded it on the lines that get from the valve to the ABS pump. I havent had time to bleed the rear breakes, but i will do that before i use it. But on a testrun the breakes works okey and i cant push it to the floor, but its seems a litle soft, is that beacuse not bleeded the rear or is there som air in the ABS pump?
I used this MC http://wheelbearings.ca/brakes-wheel...-cylinder.html
But the reservoir is inline with the cylinder so when filling it i cant get to max since all the fluid is in back of the reservoir, is this a problem? Could i replace the reservoir with the one i got on my old one since thats more tilted?
This was my first time replacing mc and calipers, its not hard/difficult if someone wonder.
I used this MC http://wheelbearings.ca/brakes-wheel...-cylinder.html
But the reservoir is inline with the cylinder so when filling it i cant get to max since all the fluid is in back of the reservoir, is this a problem? Could i replace the reservoir with the one i got on my old one since thats more tilted?
This was my first time replacing mc and calipers, its not hard/difficult if someone wonder.
Last edited by pwb; 08-05-2012 at 12:32 PM.
#2
Senior Member
Join Date: Dec 2010
Location: Norman, OK
Posts: 698
Likes: 0
Received 2 Likes
on
2 Posts
Year: 95
Model: Grand Cherokee
Engine: 4.0
Air can or may pass through the ABS hydraulic unit but you may need to bleed the 4 lines that go into it. You would bleed these 4 lines just like you would bleed the calipers other than you are loosening the actual lines instead of a bleeder screw. There is no order to doing it but all 4 of them should be bled.
The bleeding sequence is MC, ABS unit (aka HCU) at the 4 brake lines, right rear, left rear, right front, left front. Most people dont ever bother with bleeding the ABS unit so you can use your judgement if needed.
Also when bleeding the calipers/cylinders it can help to tap the caliper or wheel cylinder to insure that air bubbles are not stuck to the sides. Tapping them with a wrench or screwdriver handle will make the air bubbles travel to the top and through the bleeder (hope that makes since) Anyway you do need to bleed the rear brakes or whole system when doing a MC.
The bleeding sequence is MC, ABS unit (aka HCU) at the 4 brake lines, right rear, left rear, right front, left front. Most people dont ever bother with bleeding the ABS unit so you can use your judgement if needed.
Also when bleeding the calipers/cylinders it can help to tap the caliper or wheel cylinder to insure that air bubbles are not stuck to the sides. Tapping them with a wrench or screwdriver handle will make the air bubbles travel to the top and through the bleeder (hope that makes since) Anyway you do need to bleed the rear brakes or whole system when doing a MC.
#3
Senior Member
Thread Starter
Join Date: Mar 2011
Location: Norway
Posts: 651
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1993
Model: Grand Cherokee
Engine: 4.0L I6
Air can or may pass through the ABS hydraulic unit but you may need to bleed the 4 lines that go into it. You would bleed these 4 lines just like you would bleed the calipers other than you are loosening the actual lines instead of a bleeder screw. There is no order to doing it but all 4 of them should be bled.
The bleeding sequence is MC, ABS unit (aka HCU) at the 4 brake lines, right rear, left rear, right front, left front. Most people dont ever bother with bleeding the ABS unit so you can use your judgement if needed.
Also when bleeding the calipers/cylinders it can help to tap the caliper or wheel cylinder to insure that air bubbles are not stuck to the sides. Tapping them with a wrench or screwdriver handle will make the air bubbles travel to the top and through the bleeder (hope that makes since) Anyway you do need to bleed the rear brakes or whole system when doing a MC.
The bleeding sequence is MC, ABS unit (aka HCU) at the 4 brake lines, right rear, left rear, right front, left front. Most people dont ever bother with bleeding the ABS unit so you can use your judgement if needed.
Also when bleeding the calipers/cylinders it can help to tap the caliper or wheel cylinder to insure that air bubbles are not stuck to the sides. Tapping them with a wrench or screwdriver handle will make the air bubbles travel to the top and through the bleeder (hope that makes since) Anyway you do need to bleed the rear brakes or whole system when doing a MC.
Thread
Thread Starter
Forum
Replies
Last Post
Blackcherokee290
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
27
07-26-2022 07:52 PM
Jose Calderon
Stock Grand Cherokee Tech. All ZJ/WJ/WK Non-modified/stock questions go here!
17
09-17-2015 08:57 PM
Zeke P. Lucas
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
8
08-30-2015 05:42 PM
David Chauncey Clothier
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
2
08-29-2015 09:31 PM
Zerocyde
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
5
08-24-2015 10:56 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)