Added a radio and speakers for little money:
https://cimg0.ibsrv.net/gimg/www.che...463084cce0.jpg https://cimg1.ibsrv.net/gimg/www.che...cbd0d28462.jpg Cleaned up the rockers and lower doors: https://cimg6.ibsrv.net/gimg/www.che...735bf08706.jpg Started addressing things in the bay, motor mounts, vac harnesses, seals around the oil filter: https://cimg4.ibsrv.net/gimg/www.che...09f72aff9e.jpg https://cimg2.ibsrv.net/gimg/www.che...9a435aa045.jpg https://cimg3.ibsrv.net/gimg/www.che...485b4bc88f.jpg |
Combined two t-cases to get one to go in the jeep:
https://cimg9.ibsrv.net/gimg/www.che...6540b051b6.jpg https://cimg4.ibsrv.net/gimg/www.che...c1b1fb59d7.jpg Got some steering reinforcement in place: https://cimg8.ibsrv.net/gimg/www.che...5f7944c4eb.jpg https://cimg6.ibsrv.net/gimg/www.che...8c94338f17.jpg https://cimg9.ibsrv.net/gimg/www.che...3b5bf3b3e5.jpg Got a few more things ready for the rear axle to go in: https://cimg7.ibsrv.net/gimg/www.che...ed73095f21.jpg https://cimg9.ibsrv.net/gimg/www.che...3e96bde499.jpg https://cimg2.ibsrv.net/gimg/www.che...849a5bb8e1.jpg https://cimg4.ibsrv.net/gimg/www.che...5018293870.jpg https://cimg6.ibsrv.net/gimg/www.che...9a4b884d72.jpg https://cimg7.ibsrv.net/gimg/www.che...45d8b4f02a.jpg https://cimg8.ibsrv.net/gimg/www.che...59b3de726b.jpg https://cimg9.ibsrv.net/gimg/www.che...15db4075c8.jpg https://cimg0.ibsrv.net/gimg/www.che...ed7afb607a.jpg |
Now that the rear was taking shape, I turned my attention to the front:
https://cimg3.ibsrv.net/gimg/www.che...e85c5aa699.jpg https://cimg6.ibsrv.net/gimg/www.che...065246f656.jpg https://cimg7.ibsrv.net/gimg/www.che...9bf40cbea1.jpg https://cimg8.ibsrv.net/gimg/www.che...78e9696eaf.jpg https://cimg9.ibsrv.net/gimg/www.che...ce4ae34f96.jpg https://cimg1.ibsrv.net/gimg/www.che...70e52a1521.jpg https://cimg2.ibsrv.net/gimg/www.che...9b7fe508d6.jpg |
Here's how it was sitting after the 3 link and front springs went in:
https://cimg4.ibsrv.net/gimg/www.che...6126893fe1.jpg https://cimg8.ibsrv.net/gimg/www.che...627603c33f.jpg https://cimg1.ibsrv.net/gimg/www.che...88e6271e21.jpg https://cimg3.ibsrv.net/gimg/www.che...7e32173c7a.jpg Got a CB radio mounted up: https://cimg9.ibsrv.net/gimg/www.che...eca1de620e.jpg Picked up a warn winch in preparation for the winch bumper that is on the way: https://cimg1.ibsrv.net/gimg/www.che...9ff27d2b33.jpg |
That's pretty much up to date.
Ordered and waiting on the following to come in: DnD Slayer winch bumper CB antenna, mount, and coax Speed bleeders 35x12.50r15 KM2s on 15x8 Trailmasters |
Wowzers! You aren't wasting time are you?! Looks good.
|
|
Originally Posted by jay_sco
(Post 3181197)
Wowzers! You aren't wasting time are you?! Looks good.
|
First couple light coats of bed liner:
https://cimg8.ibsrv.net/gimg/www.che...4511e7a97b.jpg https://cimg0.ibsrv.net/gimg/www.che...8d0ab83dc3.jpg |
Looks great. Why did you go with cork gaskets and stock engine mounts? Felpro gaskets and brown dog mounts are the way to go.
|
Originally Posted by unidentifiedbomb
(Post 3181767)
Looks great. Why did you go with cork gaskets and stock engine mounts? Felpro gaskets and brown dog mounts are the way to go.
|
Can't argue with that deal. I'm rolling up to 250k without much issues, just a small oil adapter leak that I just need to find time to change.
|
Very nice build so far
|
Got a lot of little finishing things to get the front bumper done. I'm going to paint the chopped fender to cut down on the potential for rust, add door edge trim over the end of the fender and the flare to tighten up the look of the cuts, remove the air dam from the front of the jeep. Still need to get the rear bolts in the winch. I may need to cut access holes in the bumper to do so, still dreaming up solutions for that right now. Need to wire in the winch and test it..blah blah. Simple things, just need the time.
So far, I like the bumper minus the limitation of space getting the proper length bolt into the rear of the winch, but I'll figure that out. https://cimg1.ibsrv.net/gimg/www.che...e183b14d85.jpg https://cimg4.ibsrv.net/gimg/www.che...36c0810488.jpg |
All times are GMT -5. The time now is 06:37 AM. |
© 2024 MH Sub I, LLC dba Internet Brands