96 Cherokee project
#16
Junior Member
Thread Starter
Join Date: Aug 2015
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee
https://m.facebook.com/profile.php?id=232225700295441 Here's The Compound.
https://www.facebook.com/groups/339370189570236/ Here's the CJK.
https://www.facebook.com/groups/339370189570236/ Here's the CJK.
#17
Junior Member
Thread Starter
Join Date: Aug 2015
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee
This jeep gonna run my bank empty!! I guess that's what happened when you buy a jeep? Lol
Picked up a new muffler, and some spray bedliner to redo the tan **** they put on. Gonna get the exhaust finished then do that idk of i can do that today or not though. I got a thrush turbo curious to see what it sounds like lol
And also found out the rough idle problem it was the O2 sensor I hadn't plugged back up that goes before the cat becuase that's the one that actually will adjust the fuel mixture so I plugged that up and runs great now
Picked up a new muffler, and some spray bedliner to redo the tan **** they put on. Gonna get the exhaust finished then do that idk of i can do that today or not though. I got a thrush turbo curious to see what it sounds like lol
And also found out the rough idle problem it was the O2 sensor I hadn't plugged back up that goes before the cat becuase that's the one that actually will adjust the fuel mixture so I plugged that up and runs great now
#19
Junior Member
Thread Starter
Join Date: Aug 2015
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee
Got my exhaust finished and welded up. Sounds pretty good I think and sits up high and out of the way. It's a small thrush turbo muffler and it's about what I wanted so sweet here's pics. And also the new harness I had to make for the front O2 sensor because it was farther down on the new pipe then the old
#20
Junior Member
Thread Starter
Join Date: Aug 2015
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee
Got it on the road. Paid a quarter of what I bought it for to get a tag. Lol going to holopaw this weekend so I plan to get some pics. Oh and it drives good on the highway
#21
Junior Member
Thread Starter
Join Date: Aug 2015
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee
The head head gasket went out... Was in low spinning 2000 rpm and it just poped. I was like wtf! I mean it could have happened anywhere but it was at holopaw so I had a tow truck tow it back to my house. $250! Damn. Well now I have the chance to check out the cylinders and stuff.
Also found out I have a chyser 8.25 rear end. Already knew I had the high pinion fans 30 in front but didn't know what the rear was
Also found out I have a chyser 8.25 rear end. Already knew I had the high pinion fans 30 in front but didn't know what the rear was
Last edited by Crocdocs; 08-30-2015 at 06:53 AM.
#22
Junior Member
Thread Starter
Join Date: Aug 2015
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee
Got it cleaned after holopaw and took rear bumper off, gonna be replacing it sometime, and there's my bros 96 that were going to be turning into 4x4 in the next year. Head gasket set is on its way so hopefully this weekend it will be running again.
Here's a pic of the holopaw trip of my friends on his JK with a YJ seat lol
Here's a pic of the holopaw trip of my friends on his JK with a YJ seat lol
#25
Junior Member
Thread Starter
Join Date: Aug 2015
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee
#26
Junior Member
Thread Starter
Join Date: Aug 2015
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee
#28
Junior Member
Thread Starter
Join Date: Aug 2015
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee
Thanks and I feel special your first post was on my thread lol.
Well the previous owner cut the fenders but on the rear did it exactly how your not supposed to. They are rusty at the bottom so I think I will cut rear quarters. Then cut and fold and weld the rest so it's correct and adds some strength back.
And also going to be bed lining some of the rear interior panels today including the package tray. Foam comes off super easy with wire brush
Well the previous owner cut the fenders but on the rear did it exactly how your not supposed to. They are rusty at the bottom so I think I will cut rear quarters. Then cut and fold and weld the rest so it's correct and adds some strength back.
And also going to be bed lining some of the rear interior panels today including the package tray. Foam comes off super easy with wire brush
#29
Junior Member
Thread Starter
Join Date: Aug 2015
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee
#30
Junior Member
Thread Starter
Join Date: Aug 2015
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee
Got my head back from machine shop. All was good expect was super warped. Guy said it had been overheated a bunch of times which makes sense cuz when I bought it owner said new radiator, thermostat and such. Chasing a hearing problem. But hopefully will be able to get it on this weekend. Also got some injectors to try