'94 XJ cheap build
well there is what i started with nothing special. 94 ex forestry service with the 4.0, auto and NP231.
http://img.techpowerup.org/110511/3k...caf41412b9.jpg http://img.techpowerup.org/110511/3m...ebea231c3b.jpg http://img.techpowerup.org/110511/3k...753ff81675.jpg first step was to remove the rust. sanded down all of the trouble spots and hit them with rustoleum black and the wally world bedliner up to the midway body line. http://img.techpowerup.org/110513/20...-18-55_766.jpg http://img.techpowerup.org/110513/20...-19-08_261.jpg http://img.techpowerup.org/110513/20...-19-15_665.jpg some of the lift parts i got ahold of http://img.techpowerup.org/110513/20...-22-07_821.jpg hit the junkyard for some leafs to build a bastard pack http://img.techpowerup.org/110514/22..._4684059_n.jpg my buddy was very excited at the find. 6 leafs+3 overloads and the truck they were pulled from still had a 3" block. got a chance to start working on it and here is as far as i got. http://img.techpowerup.org/110514/20...-15-31_379.jpg the centerpin is installed but no bolt on it i broke the threads and snapped a hardened bolt twice... http://img.techpowerup.org/110514/20...-20-04_847.jpg drivers side is installed but the coil compressor is still installed. http://img.techpowerup.org/110514/20...-20-25_183.jpg little bit of a lift and its just a roller the right side has no ubolts... quite a height difference even were it sits right now. going to shackle the rear and put a 1" coil spacer on the front as well hopefully that will be enough to clear a set of 32x11.50s thats what my goal is for this truck |
What kind of treads you planning on getting?
|
Originally Posted by ArmyGraham
(Post 1000838)
What kind of treads you planning on getting?
|
thanks and here is were it sits right now
http://img.techpowerup.org/110516/20...-56-15_304.jpg ran out of ubolts long enough need some 6" long ones. http://img.techpowerup.org/110516/20...-55-59_538.jpg no its not sitting on the blocks threw them under just in case something slips so the axle has something to rest on. http://img.techpowerup.org/110516/20...-55-45_927.jpg this side is done its sitting about an 1" higher than were it was on the jackstand i am hoping it levels out to about here with both sets of leafs in. got longer shackles just in case. haven't decided on if i am going to put my one inch spacers into the front as well. |
Looking good
Did you use Herculiner? It wouldn't be a bad idea to bore holes at the bottom of the doors and rocker panels and flood with a little 3M rust inhibitor. Then you can just fill them in with Silicon and remove if you ever need to again. I say this because if you have covered up rust, the liner will stop the surface from spreading but it will continue to creep inside until all you have left is all rust being held together by the polyurethane.
|
Relocate fender flares
You also may want to relocate/trim the fender flares now or you'll tear them up a bit on 32's. I had 235 AT/TA's on mine before I did a 3" lift and was tearing the flares apart on the bottom from the rubbing.
|
http://img.techpowerup.org/110516/20...-50-26_187.jpg
http://img.techpowerup.org/110516/20...-50-19_784.jpg hows it look?
Originally Posted by Thick650
(Post 1002533)
Did you use Herculiner? It wouldn't be a bad idea to bore holes at the bottom of the doors and rocker panels and flood with a little 3M rust inhibitor. Then you can just fill them in with Silicon and remove if you ever need to again. I say this because if you have covered up rust, the liner will stop the surface from spreading but it will continue to creep inside until all you have left is all rust being held together by the polyurethane.
Originally Posted by Thick650
(Post 1002534)
You also may want to relocate/trim the fender flares now or you'll tear them up a bit on 32's. I had 235 AT/TA's on mine before I did a 3" lift and was tearing the flares apart on the bottom from the rubbing.
|
well i got one of the LCA's that dale gave me in.
had to press the old bolt out what a pain no idea why it was stuck... http://img.techpowerup.org/110529/20...-41-16_991.jpg got about an inch more drop out with this one in.* http://img.techpowerup.org/110529/20...-03-45_177.jpg |
well little update on this
http://img.techpowerup.org/110716/IMG_3789.jpg http://img.techpowerup.org/110716/IMG_3790.jpg http://img.techpowerup.org/110716/IMG_3791.jpg http://img.techpowerup.org/110716/IMG_3792.jpg bunch of work done front has a 5" lift rear is a 3" and i will be throwing on a shackle soon. |
sick build. i love the 2 tone paint
:devil2: |
Looks good... yeah the green and bedliner I like!
|
Originally Posted by countrycherokee
(Post 1092923)
sick build. i love the 2 tone paint
:devil2:
Originally Posted by En.Ki
(Post 1092931)
Looks good... yeah the green and bedliner I like!
|
Originally Posted by cdawall
(Post 1092941)
thanks think i should do the roof too?
|
I know I need to do that hatch its on the to do list...
Sent by my pet chicken |
Those tires and rims look great...I like the two tone paint as well. nice build.
|
All times are GMT -5. The time now is 01:17 PM. |
© 2024 MH Sub I, LLC dba Internet Brands