Alright, this is for my records:
9/5/11 Start Auto-RX de-sludge program Changed oil to Advance Auto Parts conventional 10W-30 Changed oil filter to Purlator L14619 Odometer 194,672 Avg 12mpg (short distance, in town driving) Cyl PSI 1 135 2 145 3 150 4 141 5 138 6 150 (not bad for a 24 year old vehicle, eh?) :gunsmilie: Was going to change valve cover gasket and take pictures, but ran out of time. These'll have to do for documentation purposes. Through the oil fill port: http://i268.photobucket.com/albums/j...905_170023.jpg http://i268.photobucket.com/albums/j...905_170028.jpg |
Replaced my vacuum lines using Napa's Vacuum Assemblies. 3 parts gets you all the hoses.
P/N: 715-1365, 715-1366, 715-1367 1365 comes with required grommet for valve cover. Old vs. New grommet. http://i268.photobucket.com/albums/j...930_141014.jpg Also replaced O2 sensor. 195,491 30Sep11 |
Looking good man. So whats your plans for it? Lift in the future?
|
Took a look at the rear leafs (leaves? Leafesses? A flock of leaf?) and they're starting to sag. My wife grew up with the vehicle and it holds sentimental value to her, so I'm not going to do anything too extreme to it (so I need a second XJ, right;)? ). Either replace stock or maybe 3", but for sure not higher. Just wanna dick around, learn the vehicle, and get it in great shape. The electrical connectors under the hood are very brittle and I'd like to replace the harness....but I haven't been able to come up with a suitable replacement...
|
where'd you mount the new over flow tank?
|
Originally Posted by cherokee_ftw_5
(Post 1229105)
where'd you mount the new over flow tank?
Picked up this guy from Advanced for $13 and mounted it where the old expansion tank was (remove the old tank bracket first). http://i268.photobucket.com/albums/j...r/IMG_2572.jpg A little bending and re-bending to get the tank low enough to not hit the hood... http://i268.photobucket.com/albums/j...r/IMG_2573.jpg http://i268.photobucket.com/albums/j...r/IMG_2574.jpg Use the included plastic thingy and twist ties to route the hose http://i268.photobucket.com/albums/j...r/IMG_2575.jpg Also, here are the new vacuum tubes. http://i268.photobucket.com/albums/j...r/IMG_2576.jpg http://i268.photobucket.com/albums/j...r/IMG_2577.jpg http://i268.photobucket.com/albums/j...r/IMG_2578.jpg |
11/20/11
Oil change Advance Auto Parts conventional 10W-30 Changed oil filter to Purlator L14619 Odometer 196,690 |
23 Attachment(s)
1/11/12 197,313
Had a leaky injector and parked the Waggy just after my last post. I hadn't seen a RENIX specific fuel injector write-up, so I thought I'd document what I did. My company just closed its doors, so while looking for work, we could do with one car. Picked up a set of Bosch 973's from Precision Fuel Injectors. $89.99 for 6 reman'd 19lb four hole injectors. There was a little hiccup getting them here, but I'm more than satisfied with my purchase. Loosely followed this thread. Leaky injector Attachment 386434 Disconnect battery Attachment 386435 Pop the tube from throttle body to air box off Attachment 386436 Attachment 386437 Trying to gain some room to get the rail off, take the throttle body off. Remove 3 Torx screws, disconnect cable indicated by big arrow, and disconnect 4 sensors. Remember to label everything with masking tape. Attachment 386438 Attachment 386439 Lotsa room Attachment 386440 Disconnect the plug from each injector, making sure to label everything. There is a metal clip that needs to be removed before the plug comes off. A small flat-blade does the trick. Keep them. Arrow indicates installed clip Attachment 386441 Remove the 4 bolts that hold the rail in. Disconnect the front and rear fuel lines. Simply pinch the plastic pieces and pull the line. I had the o-ring for the rear line come out. Just re-installed it. Attachment 386442 Attachment 386443 Attachment 386444 Disconnect the vacuum line from the fuel regulator and the front fuel line. I got mine to disconnect, but couldn't remove it until I removed the rail. Attachment 386445 Carefully wiggle the fuel rail until all 6 injectors come loose. Make sure their o-rings come out with them. Attachment 386446 Attachment 386447 Pretty gunked up in the ports in the head. Broke out the shop vac and scraped them clean. Don't let any of that crap fall into the head. Bad joo-joo. Attachment 386448 Remove the metal clips holding the injector to the fuel rail. Keep them and clean them. Attachment 386449 I cleaned up the rail, then on to the new injectors. Attachment 386450 Attachment 386451 Attachment 386452 Use some motor oil and lube up the o-rings on both ends. Install on fuel rail. Attachment 386453 Attachment 386454 Prep the holes by cleaning them. Attachment 386455 Reverse all steps and reassemble :001_tongue: Attachment 386456 Reconnect the battery and turn your key to the "on" position. This powers the fuel pump and pressurizes the system. Check for leaks. Off to the races!:cheers: About an hour and a half start to finish. |
also i dont know if you mentioned it but i think your suppose to take the gas cap off to release the pressure in the lines
|
1 Attachment(s)
Originally Posted by Dimebagdave916
(Post 1457897)
also i dont know if you mentioned it but i think your suppose to take the gas cap off to release the pressure in the lines
Attachment 386413 |
4 Attachment(s)
2/9/12
Just a couple simple housekeeping things. Swapped the fan belt - that was an interesting experience. 4 bolts need loosening, then you can turn the adjustment bolt on the power steering pump. The 2 back bolts and the bottom front bolt can be gotten most easily from the bottom, while the top bolt on the front can be gotten from above. Turning the adjustment bolt can be done from the bottom with a ratchet or from the top with a ratchet with two 6" extensions and a u-joint. PB Blaster makes things easier. Attachment 383153 Next, did the old "ground refresh." Swapped the tiny ribbon cable from the head to the firewall with a 19" 4 gage cable. Cleaned the connection with a wire brush and some throttle body cleaner, then put the new one on. Attachment 383154 Did the same with the "dip stick" set. Attachment 383155 Next, took off the Throttle body and cleaned it up nice and shiny. Also removed the IAC and gave it a good scrubbing. Noticeably smoothed out the idle. Attachment 383156 Figuring out the belt was by far the most time consuming part. |
5 Attachment(s)
2/14/12
I'm trying to slowly get rid of all the fluid leaks. Yesterday it was time to do the distributor mount gasket. Pretty simple procedure, if you don't dick with the crank position while the distributor is out.... :furious: Marked and unplugged a couple of the plug wires, as well as the coil wire. Took the cap off and tucked it away. Attachment 383148 Marked the position of the distributor to the block using white out. Also, position of the rotor to the housing, then removed the bolt (1/2" combination wrench will get it done). Disconnect the cable coming out the the distributor and slowly pull up and out on everything. Attachment 383149 Attachment 383150 Clean the old gasket from around the hole, clean up the mounting bracket and wipe down the distributor (don't remove your marks....). Attachment 383151 I had some sludge in my distributor, but some careful work with q-tips and throttle body cleaner fixed that. Attachment 383152 Now, if you were careful, you could just slide everything back in. I, on the other hand, had to locate TDC for the #1 cyl, then do the process. Since it was just me, I pulled the plug and installed my compression gage. Using a ratchet, I rotated the crank once (using markers on the pulley and timing chain cover) and checked if I had generated any pressure. First time there wasn't any, which means that was the exhaust stroke. Once more confirmed by pressure to be TDC on the compression stroke, so off to the races. Turned the oil pump slot in the block with a screwdriver and everything went together just fine, with the rotor pointing at the #1 cyl contact on the cap. Done and done. |
Sweet man, looking good! I did the same with the ground strap, but the dipstick ones I need to get too, what did you exactly do? I have yet to do my distributor gasket as well.
|
Originally Posted by alsxj
(Post 1539908)
Sweet man, looking good! I did the same with the ground strap, but the dipstick ones I need to get too, what did you exactly do? I have yet to do my distributor gasket as well.
|
26 Attachment(s)
3/11/12
199,340 Oil change Advance Auto Parts conventional 10W-30 Changed oil filter to Purlator L14619 Going through and replacing the gaskets and seals that have been neglected. Trying to get my Waggy drip-free. The goal today was valve cover, oil filter adapter o-rings, rear main, and oil pan. Ambitious, I know. Didn't quite make the rear main or oil pan....some other day, I guess. First thing I learned was not to jack up your vehicle in prep for the oil pan/rear main before doing the valve cover....I'm 6ft tall, but even so it was difficult swapping that gasket with the Jeep on stands.:brickwall: Had oil on the bottom of the pan, so a week ago, I sprayed it down with Engine Brite and power washed it, hoping to pinpoint the leak. The two I could verify was back of the valve cover and filter adapter. Attachment 379765 Disconnected the cruise control cable and the two CCV tubes from the valve cover. Took out all the bolts and the 3 studs and laid them out in their proper order. Attachment 379766 Attachment 379767 Had to remove the three screws holding this thingy to the firewall so I would have enough clearance to get the valve cover off. Attachment 379768 The last time this was done, the gasket was made with a thick bead of RTV....a real PITA to get off.... Attachment 379769 Scraped it clean and then used brake cleaner to ensure gasket surface was ready to go. Attachment 379770 Random pics to document condition: Attachment 379771 Attachment 379771 Valve cover itself took about an hour with a brass brush, 2 cans of brake cleaner and a roll of paper towels to clean. Took off the little snorkel intake thingys that the CCV system connect to and cleaned them. Next time the cover's off, I'll cut 'em and drill the vent hole as is recommended. Attachment 379773 Attachment 379774 Before I go on, the back bolt is best reached from the driver's side using a socket, a u-joint, then two 6" extensions. Install new $40 Fel-pro blue gasket sans RTV of any sort, paying attention to the "this side up" markings, then re-installed the cover. Attachment 379775 Haynes stated that the bolts/studs should be torqued to 55 in-lbs, but that was barely finger tight (4ish ft-lbs). Found online that some guys recommended 80ish in-lbs (6.66 ft-lbs), so that's what I torqued to. Started with the centre bolts and alternated sides as I worked towards the ends. Next, time for the Oil Filter Adapter O-rings. You will need 3 o-rings and I had to go to the dealer for them. Here are the dealer part numbers (THESE ARE RENIX ONLY PART NUMBERS - HO's have different o-rings): 33002970 o-ring 0.799 x 0.103 33002971 o-ring 1.296 x 0.130 33002972 o-ring Oil Filter AD Taken from here. Attachment 379776 Attachment 379777 Clearly I'm leaking oil here: Attachment 379778 I'm one of the lucky ones that doesn't have to mess around with a T60 torx or an allen head. 5/8" socket and a "breaker bar" got me on the way. Attachment 379779 Attachment 379780 Be sure you've drained your oil and removed your filter. It's also a good idea to soak up the extra oil in that adapter as it will all spill on you when you take it off. Attachment 379781 Attachment 379782 Beware the drips Attachment 379783 And remove the bolt. Attachment 379784 Don't worry about marking the angle of the adapter relative to the block or anything like that. There is a dowel that sticks out from the block and it can only be put on one way. Remove from the block. Attachment 379785 My o-rings were rock hard and squared off. Definitely time to replace. Attachment 379786 The new vs the old. Attachment 379787 Attachment 379776 Clean it up, install the new o-rings (lube with oil so as not to roll or tear them as they're installed) Attachment 379789 Attachment 379790 Put it all back together, carefully, and tighten 'er down. I couldn't find a torque spec, so I just kept cranking.... Sun was going down, despite Day Light Savings, so I decided to wait on the rear main and oil pan gasket. Cleaned everything under the car really well and we'll see if those two fixed my problem.... Cheers. |
All times are GMT -5. The time now is 10:10 PM. |
© 2024 MH Sub I, LLC dba Internet Brands