Renix system on 1992 Jeep commanche?
#1
Junior Member
Thread Starter
Renix system on 1992 Jeep commanche?
Been working on my commanche project, 2-wheel drive to 4x4.
swapped out motor ,tranny . Added tcase front diff and a older motor, 88-89 H.o type.
So far no start.
Did an1992 commanche come with a renix system ?.
All the info I find says that's what was in this 92.
Used flexplate, distributor, new, aND existing wiring in truck.
nothing is working to get spark, new c.p.s new distributor, lowered c.p.s by drilling out top hole to 3/8 still no fire.
When key is on reading c.p.s wires I have 12v on center top pin. 3.5v on one lower pin and 6-7v on other pin. Tried testing them every way possible even the AC .5 with it unplugged while cranking engine get nothing. Getting bummed.
Any ideas out there other than take it to a shop. No money, have to figure it out at home.
Thanks in advance
swapped out motor ,tranny . Added tcase front diff and a older motor, 88-89 H.o type.
So far no start.
Did an1992 commanche come with a renix system ?.
All the info I find says that's what was in this 92.
Used flexplate, distributor, new, aND existing wiring in truck.
nothing is working to get spark, new c.p.s new distributor, lowered c.p.s by drilling out top hole to 3/8 still no fire.
When key is on reading c.p.s wires I have 12v on center top pin. 3.5v on one lower pin and 6-7v on other pin. Tried testing them every way possible even the AC .5 with it unplugged while cranking engine get nothing. Getting bummed.
Any ideas out there other than take it to a shop. No money, have to figure it out at home.
Thanks in advance
#2
Moderator of Jeeps
Join Date: Jul 2011
Location: Frederick, MD from Cleveland, OH
Posts: 21,029
Likes: 0
Received 3 Likes
on
3 Posts
Year: 1993 YJ Wrangler
Engine: 4.0 I6
I can't help you with all the swap details, but the '92 was not a Renix system. It is, however, the rarest year of the Comanche. That's a desirable truck.
'87-90 Renix
'91 "High Output" engine, but still has the Center Axle Disconnect
'92 HO and one--piece axle shafts
'87-90 Renix
'91 "High Output" engine, but still has the Center Axle Disconnect
'92 HO and one--piece axle shafts
#3
::CF Moderator::
Join Date: Aug 2011
Location: Prescott, Az
Posts: 43,874
Received 1,526 Likes
on
1,238 Posts
Year: 1990
Model: Cherokee (XJ)
Engine: 4.0
Been working on my commanche project, 2-wheel drive to 4x4.
swapped out motor ,tranny . Added tcase front diff and a older motor, 88-89 H.o type.
So far no start.
Did an1992 commanche come with a renix system ?.
All the info I find says that's what was in this 92.
Used flexplate, distributor, new, aND existing wiring in truck.
nothing is working to get spark, new c.p.s new distributor, lowered c.p.s by drilling out top hole to 3/8 still no fire.
When key is on reading c.p.s wires I have 12v on center top pin. 3.5v on one lower pin and 6-7v on other pin. Tried testing them every way possible even the AC .5 with it unplugged while cranking engine get nothing. Getting bummed.
Any ideas out there other than take it to a shop. No money, have to figure it out at home.
Thanks in advance
swapped out motor ,tranny . Added tcase front diff and a older motor, 88-89 H.o type.
So far no start.
Did an1992 commanche come with a renix system ?.
All the info I find says that's what was in this 92.
Used flexplate, distributor, new, aND existing wiring in truck.
nothing is working to get spark, new c.p.s new distributor, lowered c.p.s by drilling out top hole to 3/8 still no fire.
When key is on reading c.p.s wires I have 12v on center top pin. 3.5v on one lower pin and 6-7v on other pin. Tried testing them every way possible even the AC .5 with it unplugged while cranking engine get nothing. Getting bummed.
Any ideas out there other than take it to a shop. No money, have to figure it out at home.
Thanks in advance
Which flywheel/flexplate did you use?
http://cruiser54.com/?p=100
Thread
Thread Starter
Forum
Replies
Last Post
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)