Removing Oil Pan.
#1
Junior Member
Thread Starter
Join Date: Nov 2010
Location: Ohio
Posts: 83
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: Straight 6 4.0L
Removing Oil Pan.
Does anyone know of a good walk though of how to remove the oil pan on my Cherokee? I've been looking on google and cant really find one.
#2
Member
#3
CF Veteran
Join Date: May 2010
Location: Western Michigan
Posts: 1,680
Likes: 0
Received 4 Likes
on
4 Posts
Year: 1993
Model: Grand Cherokee
Engine: 4.0l inline 6
Oil Pan
Search is your friend...... I found this with a easy few clicks in the search box. It doesnt give step by step but it does give some good ideas.
https://www.cherokeeforum.com/f2/oil-pan-83649/
basicly your removeing bolts. But get the one peice gasket.
https://www.cherokeeforum.com/f2/oil-pan-83649/
basicly your removeing bolts. But get the one peice gasket.
#4
- Disconnect negative cable from battery.
- Raise the vehicle.
- Remove the oil pan drain plug and drain the engine oil.
- Disconnect the exhaust pipe at the exhaust manifold.
- Disconnect the exhaust hanger at the catalytic converter and lower the pipe.
- Remove the starter motor.
- Remove the engine flywheel and transmission torque converter housing access cover.
- If equipped with an oil level sensor, disconnect the sensor.
- Position a jack stand directly under the engine vibration damper.
- Place a piece of wood (2 x 2) between the jack stand and the engine vibration damper.
- Remove the engine mount through bolts.
- Using the jack stand, raise the engine until adequate clearance is obtained to remove the oil pan.
- Remove transmission oil cooling lines (if equipped) and oxygen sensor wiring supports that are attached to the oil pan studs.
- Remove the oil pan bolts and studs. Carefully slide the oil pan and gasket to the rear. If equipped with an oil level sensor, take care not to damage the sensor.
#6
CF Veteran
Join Date: Mar 2010
Location: Broward County Fl.
Posts: 47,923
Likes: 0
Received 22 Likes
on
22 Posts
Year: 1989 xj sport 2dr
Model: Cherokee
Engine: 12 hole bosch Injectors
- Disconnect negative cable from battery.
- Raise the vehicle.
- Remove the oil pan drain plug and drain the engine oil.
- Disconnect the exhaust pipe at the exhaust manifold.
- Disconnect the exhaust hanger at the catalytic converter and lower the pipe.
- Remove the starter motor.
- Remove the engine flywheel and transmission torque converter housing access cover.
- If equipped with an oil level sensor, disconnect the sensor.
- Position a jack stand directly under the engine vibration damper.
- Place a piece of wood (2 x 2) between the jack stand and the engine vibration damper.
- Remove the engine mount through bolts.
- Using the jack stand, raise the engine until adequate clearance is obtained to remove the oil pan.
- Remove transmission oil cooling lines (if equipped) and oxygen sensor wiring supports that are attached to the oil pan studs.
- Remove the oil pan bolts and studs. Carefully slide the oil pan and gasket to the rear. If equipped with an oil level sensor, take care not to damage the sensor.
Thread
Thread Starter
Forum
Replies
Last Post
93civEJ1
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
6
10-02-2019 04:08 AM
JamDeeper
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
0
09-08-2015 08:50 PM
ARCH4NGEL_II
Modified XJ Cherokee Tech
0
09-07-2015 12:18 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)