What did you do to your Cherokee today?
CF Veteran
They're stronger than what most say, all depends on the type of driving and future plans for your Jeep. I'm staying with 31s with a DD/Weekend warrior of mild trails mentality so I'm not worried about breaking it, might as well give it a great cover in case of an encounter with a rock.
CF Veteran
Join Date: May 2010
Location: Fort Collins, CO
Posts: 3,405
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1996
Model: Cherokee
Engine: 4.0L HO
Yesterday welded my Rusty's heavy duty lower control arm brackets to my Dana 30. Welds aren't pretty since I use a stick welder but they aren't going anywhere
CF Veteran
Join Date: Apr 2008
Location: Burlington, NC
Posts: 2,340
Likes: 0
Received 8 Likes
on
8 Posts
Year: 1994...mostly...
Model: Cherokee (XJ)
Engine: 4.0L I6 HO, Lot's of Bolt Ons
Installed a bored throttle body from:
thexjfiles
Loom him up on here, I just drove 60 miles on mine and can really tell a difference in the overall responsiveness of the Jeep.
thexjfiles
Loom him up on here, I just drove 60 miles on mine and can really tell a difference in the overall responsiveness of the Jeep.
Last edited by Desertfox1023; 04-17-2014 at 05:55 AM.
CF Veteran
Join Date: Jul 2012
Location: San Antonio, TX
Posts: 4,104
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1996
Model: Cherokee
Engine: 4.0L
Junior Member
Join Date: Feb 2014
Location: Washington
Posts: 88
Likes: 0
Received 1 Like
on
1 Post
Year: 1990
Model: Cherokee
Engine: 4.0
Welded 30 bolts into the metal backers so I can re-install the factory flares. (There are actually 32 bolts, but 2 actually survived the removal process!)
I went through quite a few drill bits drilling out the broken off studs - time to restock when I catch them on sale at HF.
Then put a quick coat of primer on them and they'll be ready to install tomorrow.
I went through quite a few drill bits drilling out the broken off studs - time to restock when I catch them on sale at HF.
Then put a quick coat of primer on them and they'll be ready to install tomorrow.
Moderator of Jeeps
Join Date: Jul 2011
Location: Frederick, MD from Cleveland, OH
Posts: 21,029
Likes: 0
Received 3 Likes
on
3 Posts
Year: 1993 YJ Wrangler
Engine: 4.0 I6
Seasoned Member
Join Date: Mar 2014
Location: Los Angeles
Posts: 352
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0
Picked up my winch bumper from Dirtbound today. I sprayed some primer then like 4 coats of vht roll bar chassis satin black. Then I tried installing it and snapped off two of the three bolts for the steering box lol. Luckily I had a new (rebuilt one) steering box in my garage since the one in the cherokee is the exact same one for my 70 Chevy Monte Carlo.
Bought new bolts for it and new hoses since those where rusted stuck too. Man I swear my 99 xj is a rust bucket compared to my 45 year old car. Lol. -_-
Bought new bolts for it and new hoses since those where rusted stuck too. Man I swear my 99 xj is a rust bucket compared to my 45 year old car. Lol. -_-
Senior Member
Join Date: Jan 2011
Location: Green Bay Wisconsin
Posts: 677
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0L High Output
I'll post pictures later.
It half counts as today. I worked on my jeep for 20 hours doing different things.
O2 sensor. Map sensor. Oil change. Rebuilt the double cardan drive shaft for the rear. And did s10 leaf springs with shims.
The leaf springs took forever. It sits at what I'm assuming is either 3.5 or 4. Its a little bit taller then the front which is 3.
Tomorrow I will install the drive shaft and hopefully get tires and an alignment done.
It half counts as today. I worked on my jeep for 20 hours doing different things.
O2 sensor. Map sensor. Oil change. Rebuilt the double cardan drive shaft for the rear. And did s10 leaf springs with shims.
The leaf springs took forever. It sits at what I'm assuming is either 3.5 or 4. Its a little bit taller then the front which is 3.
Tomorrow I will install the drive shaft and hopefully get tires and an alignment done.
Senior Member
Join Date: Jul 2013
Location: Maine
Posts: 799
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: 4.0
...Woke up to brush fresh snow off it yesterday...Still had snow and icicles on it when I got out of school and track practice, when it had been parked in the sun all day.
FYI it's 22 degrees fahrenheit as I type this...Supposed to get to 30s as the day goes on...
FYI it's 22 degrees fahrenheit as I type this...Supposed to get to 30s as the day goes on...