Last edit by: IB Advertising
See related guides and technical advice from our community experts:
Browse all: Steering & Suspension
- Jeep Grand Cherokee ZJ WJ 1993 to 2004 How to Replace Wheel Hub Bearing
Step by step instructions for do-it-yourself repairs.
Browse all: Steering & Suspension
replacing wheel bearings how much think it would cost?
#1
CF Veteran
Thread Starter
Join Date: Oct 2010
Location: Salem Nh
Posts: 1,756
Likes: 0
Received 1 Like
on
1 Post
Year: 1998
Model: Cherokee
Engine: 4.0
replacing wheel bearings how much think it would cost?
im going to get my 4 wheel bearings replaced tomorrow as well as the u joints in the rear shaft, anyone have any idea on how much it will cost roughly? if its to much for all 4 ill just get the rear bearings done and then the fronts another time
#2
Honorary Moderator
Join Date: Mar 2010
Location: Gilbert AZ/Las Cruces NM
Posts: 8,135
Likes: 0
Received 13 Likes
on
11 Posts
Year: 1996
Model: Cherokee
Engine: 4.0 upgraded
Parts + ~$100 for labor/hr
it is going to be probably about $600-$800 or more
you can do it yourself for about $300(max) using Tikmen wheel bearings and HD Spicer u-joints (all 6) in your driveway.
it is going to be probably about $600-$800 or more
you can do it yourself for about $300(max) using Tikmen wheel bearings and HD Spicer u-joints (all 6) in your driveway.
#6
CF Veteran
Join Date: Sep 2009
Location: Grand Prairie, Texas
Posts: 1,142
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1998
Model: Cherokee
Engine: 4.0 HO I6
Mitchell says 2 hours per side for the fronts, 2.5 total for the rear. So 4.5 hours of labor plus about $300 in parts. That puts it around $600-$800.
You can get the timken wheel bearings for $75 a piece for fronts. The fronts are easy, the whole hub assembly comes off and you just slap the new one on. 1 36mm nut and 3 12pt 13mm bolts and tap it off.
You can get the timken wheel bearings for $75 a piece for fronts. The fronts are easy, the whole hub assembly comes off and you just slap the new one on. 1 36mm nut and 3 12pt 13mm bolts and tap it off.
#7
CF Veteran
Join Date: Apr 2009
Location: Kalamazoo, MI
Posts: 1,601
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: 4.0L with throttle body spacer and cold air intake, bored throttle body, #784 injector upgrade
Mitchell says 2 hours per side for the fronts, 2.5 total for the rear. So 4.5 hours of labor plus about $300 in parts. That puts it around $600-$800.
You can get the timken wheel bearings for $75 a piece for fronts. The fronts are easy, the whole hub assembly comes off and you just slap the new one on. 1 36mm nut and 3 12pt 13mm bolts and tap it off.
You can get the timken wheel bearings for $75 a piece for fronts. The fronts are easy, the whole hub assembly comes off and you just slap the new one on. 1 36mm nut and 3 12pt 13mm bolts and tap it off.
Trending Topics
#8
CF Veteran
Join Date: Sep 2010
Location: Warsaw, IN
Posts: 2,844
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000,1990,1999
Model: Cherokee
Engine: 4.0
#9
Member
Join Date: Nov 2009
Location: East Coast
Posts: 176
Likes: 0
Received 0 Likes
on
0 Posts
Year: This one's a 96'....
Model: Cherokee
Engine: 4.0
Depends you can get a $75 bearing assembly or a $250 one........take the brake caliper and disk off, 3 bolts in the back, and one big axle nut.........rinse and repeat........easy to do.
#10
CF Veteran
Join Date: Sep 2009
Location: Knoxville, TN
Posts: 1,471
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1998
Model: Cherokee
Engine: 4.0 inline 6 (o yea!)
$600-800 for a wheel bearing on a Pontiac G6? Man, someone is royally bending you over the oak barrel. Are you sore? Unless its for this g6
Then I could understand
OP, wheel bearings are easy to do in the front and are normally around $80 each from Autozone. It takes a 1/2" 12 point socket and a 36mm nut and a little bit of time (depending on how stuck the hub is in the knuckle and the splines in the bearing). The rears are not hard either but require a little more effort to pull them from the axle tube. I ended up using a die grinder and cut the rear bearings in half. You will have to drain the rear diff and remove the c-clips and axles (also not very hard).
Then I could understand
OP, wheel bearings are easy to do in the front and are normally around $80 each from Autozone. It takes a 1/2" 12 point socket and a 36mm nut and a little bit of time (depending on how stuck the hub is in the knuckle and the splines in the bearing). The rears are not hard either but require a little more effort to pull them from the axle tube. I ended up using a die grinder and cut the rear bearings in half. You will have to drain the rear diff and remove the c-clips and axles (also not very hard).
#11
Senior Member
Join Date: Feb 2011
Location: Bel Air, Maryland 21015
Posts: 719
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0
My 96 XJ is beginning to exhibit a bearing going bad ..... noise when I turn right but not when I turn left.
I guess this means a bearing on the left side as when you turn right weight is shifted to the left.
Anyhow, I hope to make it to the spring so I can do the job myself.
It's a big job, but doesn't seem like a difficult one.
I have to install a new distributor as well and doing that bothers me more than doing the wheel bearings.
I guess this means a bearing on the left side as when you turn right weight is shifted to the left.
Anyhow, I hope to make it to the spring so I can do the job myself.
It's a big job, but doesn't seem like a difficult one.
I have to install a new distributor as well and doing that bothers me more than doing the wheel bearings.
#12
CF Veteran
Join Date: Sep 2010
Location: Warsaw, IN
Posts: 2,844
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000,1990,1999
Model: Cherokee
Engine: 4.0
Originally Posted by sgtskid
$600-800 for a wheel bearing on a Pontiac G6? Man, someone is royally bending you over the oak barrel. Are you sore? Unless its for this g6
Then I could understand
OP, wheel bearings are easy to do in the front and are normally around $80 each from Autozone. It takes a 1/2" 12 point socket and a 36mm nut and a little bit of time (depending on how stuck the hub is in the knuckle and the splines in the bearing). The rears are not hard either but require a little more effort to pull them from the axle tube. I ended up using a die grinder and cut the rear bearings in half. You will have to drain the rear diff and remove the c-clips and axles (also not very hard).
Read it over again. BEARINGS is plural. The OP is talking about replacing ALL FOUR.
#13
Junior Member
Join Date: Sep 2010
Location: SC
Posts: 92
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0
Thread
Thread Starter
Forum
Replies
Last Post
clark40
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
1
08-28-2015 07:11 AM
thebyus
Modified XJ Cherokee Tech
3
08-25-2015 06:02 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)