krkx93

wut kind of bender could i get to bend at least 1.75 in. pipe without breaking the bank?

__________________
no half measures...
build thread. check it out
http://www.cherokeeforum.com/f46/down-south-jeep-30873/

caged

if you're bending pipe, you want a pipe bender, one from harbor freight.
if you're bending tube, you want a tube bender, one from pro-tools.
you can't bend one with the other, it just won't work.

also, pipe is for poop.
tube is for your jeep.

__________________
Epic Beard Man for the win

a Jeep with out mud on it is really only a Chevy Trail Blazer - willys55

4.3L XJ

Take a piece if your pipe down to your local tool store and see if it fits one of the mandrels on their pipe bender. They are about $75

krkx93

yea but i want sumthing that i can bend somthing with some thick walls. for roll cages and stuff

__________________
no half measures...
build thread. check it out
http://www.cherokeeforum.com/f46/down-south-jeep-30873/

lil_red_wagon

[quote=caged;300053
you can't bend one with the other, it just won't work.
[/quote]

i have to argue that to a extent. even on pro-tools web site like you recommended they say their bender with do both tube and pipe. its the dies that are different. one is machined for O.D. and one is machined for I.D. sizes. so on that note you can get one bender for both apps. just have to have different sets of dies.

the one on harbor freight "says" it will do 5/8 solid square or solid round and up to 3" but it dont say tube or pipe. with the price im assuming its pipe like exhaust type of stuff. you could probable get it to work on tube it just wont fit as tight in the dies because Tube is measured by O.D. and Pipe is measured I.D.

now if you have a tube bender you wont be able to bend pipe cause the pipe wont fit inside the dies it will be too big

__________________
'90 Cherokee 4.0l, NP231 w/SYE, non-disco HPd30, d35, lincoln locked, 6in lift, 4.10s, 33's, custom crossover steering & adj track bar, removable doors, TCU control box, on board air, make due front bumper, W.O.R.P. Off Road rear bumper, tire carrier, & rock sliders, open cooling system

caged

that's right, pipe is measured by inner diameter, cause stuff usually flows through it. and tube is measured by outer diameter.

so yeah, a 2 inch pipe will usually be larger than a 2 inch tube.
so if you put a piece of tube in a pipe bender, you'll just end up kinking it.

but yeah, technically the difference is the dies.

__________________
Epic Beard Man for the win

a Jeep with out mud on it is really only a Chevy Trail Blazer - willys55

krkx93

i just need to bend pipe i want to fab tube doors and bumpers and stuff but the lack of a pipe bender has been holding me back a bit

__________________
no half measures...
build thread. check it out
http://www.cherokeeforum.com/f46/down-south-jeep-30873/

FrankZ

You do not want a pipe bender. A tubing bender is the only way to go. If you try to use a pipe bender your TUBE will kink.

D.O.M is is tubing
HREW is tubing.
Black iron (used for gas and water lines) is PIPE.

This is the TUBE BENDER that I use.
http://www.gottrikes.com/Tube_Bender.htm

__________________
9/11 - WE WILL NEVER FORGET!! (<---<< click)

krkx93

lol i dont want to bend tube at all though. i want to bend pipe. i dont want to mess with tube at all

__________________
no half measures...
build thread. check it out
http://www.cherokeeforum.com/f46/down-south-jeep-30873/

FrankZ

Why would you want to use a weak material for anything on your rig? Pipe is not strong enough for anything other than poop.

__________________
9/11 - WE WILL NEVER FORGET!! (<---<< click)

warrpath4x4

There's lots of ways to make your own bender but you will still be buying dies. I got my protools 105HD from keith flux on pirate for pretty cheap comparativly.

You don't wanna mess with tube but yet you said rollcage lol.
You realize pipe is heavier than tube also.

__________________
AMSOIL DEALER

MEMBER OF: wheelers for the wounded, blue ribbon coalition, and tread lightly

krkx93

i like the way it looks and im gunna use pipe with some real thick walls i dont like the way square tubing looks

__________________
no half measures...
build thread. check it out
http://www.cherokeeforum.com/f46/down-south-jeep-30873/

warrpath4x4

LMFAO the only one talking square tube is you.

Ok I'm sone laughing. DOM is round tube. Tube and pipe are both round but different

__________________
AMSOIL DEALER

MEMBER OF: wheelers for the wounded, blue ribbon coalition, and tread lightly

krkx93

oh lol i always thought tube was square and pipe was round. thats where i was gettin the hell confused outa me. so let me get this straight...... a tube bender is what i need???? and what kind of place carries round tube?

__________________
no half measures...
build thread. check it out
http://www.cherokeeforum.com/f46/down-south-jeep-30873/

warrpath4x4

Your local metal yard should have it, can order it, or point you in the right direction.

First I'd suggest researching DOM, HREW, and pipe. Structurally you want DOM, pipe is fine for bumpers and stuff but it does weigh more.

__________________
AMSOIL DEALER

MEMBER OF: wheelers for the wounded, blue ribbon coalition, and tread lightly