Thresholds for ZJ
#1
Senior Member
Thread Starter
Join Date: Aug 2008
Location: Locust Grove, OK
Posts: 855
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1994
Model: Grand Cherokee
Engine: 5.2 V8
Thresholds for ZJ
Here is a write up for the Grand Cherokee (ZJ) Threashholds From Howler GT.
Packing was very good I might add!!!
Here are screws provided. Thats alot of wrapping by the way. lol.
Here is everything I need.
Tools Needed:
-Drill
-7/64" drill bit
-Sharpie
-Phillips Screwdriver
-Flat Head Screwdriver
(These are tools I used, Product come with other directions and tools needed)
This is before:
Front
Back
Remove old seal with screw driver just by placeing flathead screwdrive under the seal and pry up in several places.
Repeat for real seal too.
Here is what it looks like after remove of seal:
Clean area while you have it apart(why not, right?)
Repeat for rear seal
Area after cleaned:
Place NEW seal down in place of old one. Mark with sharpie while new seal is down. Mark holes were you will drill your holes.
(Drill holes must be smaller than screws)
Like this:
Repeat for real seal
Now drill only were holes are marked.
Repeat for rear seal
Place NEW seal back in place and screw down with screws provided.
Repeat for rear seal.
Will have finished pictures tmrw. I ran out of daylight and pictures with flashlight are not very good.
I am very very happy about my purchase. These stand out quiet well. They will look dang good with doors off over summer.
P.S. I do not recremend Black&Decker products. lol
Packing was very good I might add!!!
Here are screws provided. Thats alot of wrapping by the way. lol.
Here is everything I need.
Tools Needed:
-Drill
-7/64" drill bit
-Sharpie
-Phillips Screwdriver
-Flat Head Screwdriver
(These are tools I used, Product come with other directions and tools needed)
This is before:
Front
Back
Remove old seal with screw driver just by placeing flathead screwdrive under the seal and pry up in several places.
Repeat for real seal too.
Here is what it looks like after remove of seal:
Clean area while you have it apart(why not, right?)
Repeat for rear seal
Area after cleaned:
Place NEW seal down in place of old one. Mark with sharpie while new seal is down. Mark holes were you will drill your holes.
(Drill holes must be smaller than screws)
Like this:
Repeat for real seal
Now drill only were holes are marked.
Repeat for rear seal
Place NEW seal back in place and screw down with screws provided.
Repeat for rear seal.
Will have finished pictures tmrw. I ran out of daylight and pictures with flashlight are not very good.
I am very very happy about my purchase. These stand out quiet well. They will look dang good with doors off over summer.
P.S. I do not recremend Black&Decker products. lol
#2
Senior Member
Thread Starter
Join Date: Aug 2008
Location: Locust Grove, OK
Posts: 855
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1994
Model: Grand Cherokee
Engine: 5.2 V8
Finishes Pictures!!!
Passenger Side
Drivers Side
Front Drivers Side up close
Back Drivers Side up close
Passenger Side
Drivers Side
Front Drivers Side up close
Back Drivers Side up close
Thread
Thread Starter
Forum
Replies
Last Post
Blackcherokee290
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
27
07-26-2022 07:52 PM
Howler_GT
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
6
08-19-2008 06:58 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)