Last edit by: IB Advertising
See related guides and technical advice from our community experts:
Browse all: Steering & Suspension
- Jeep Grand Cherokee ZJ WJ 1993 to 2004 How to Replace Wheel Hub Bearing
Step by step instructions for do-it-yourself repairs.
Browse all: Steering & Suspension
Problems replacing wheel bearing/hub
#1
Junior Member
Thread Starter
Join Date: Nov 2009
Location: Columbus, OH
Posts: 79
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0L
Problems replacing wheel bearing/hub
So I just bought a 1999 Jeep Cherokee Sport, and I'm in love with already. It has a few "presents" that the previous owner may have forgotten to mention, however, and I'm trying to take care of some of them myself.
First up is replacing the wheel bearings, since it has 170k miles and apparently still has the original wheel bearings (and rotors, too).
I've removed everything down to the hub assembly, but now I'm stuck. The hub is hopelessly fused to the brake dust shield/axle, and I can't get it free. I've been using PB blaster and hitting it with a rubber mallet and even a dead blow hammer and the thing will not come off. It's apparently completely rusted on there. So for anyone that has replaced the hubs, any suggestions?
First up is replacing the wheel bearings, since it has 170k miles and apparently still has the original wheel bearings (and rotors, too).
I've removed everything down to the hub assembly, but now I'm stuck. The hub is hopelessly fused to the brake dust shield/axle, and I can't get it free. I've been using PB blaster and hitting it with a rubber mallet and even a dead blow hammer and the thing will not come off. It's apparently completely rusted on there. So for anyone that has replaced the hubs, any suggestions?
#4
Seasoned Member
Join Date: Jun 2009
Location: Royal Oak, MI/Higgins Lake, MI
Posts: 287
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1997
Model: Cherokee
Engine: 4.0 liter H.O. I-6
you should be able to wedge an 3 inch extension where the axle shaft comes out of the axle. I will try and explain this. I placed a 3 inch extension with one end of the extension on the edge of the axle and the other end against wheel hub. when I turned the wheel to the right it popped the hub off. I got the idea from a write up i found on line. I will look for it and if I find I will post up.
#6
Senior Member
Join Date: Oct 2009
Location: Redlands, CA
Posts: 502
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1992
Model: Cherokee
Engine: 4.0L I6
Wow! That's a good idea (if it works without breaking anything)! I busted mine loose with a mini sledgehammer and a screwdriver. I had to work on it for a bit but if you work it out one corner at a time its no problem.
There's a lip inside the nuckle so the hubs in there pretty good!
There's a lip inside the nuckle so the hubs in there pretty good!
Trending Topics
#9
Junior Member
Thread Starter
Join Date: Nov 2009
Location: Columbus, OH
Posts: 79
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0L
FYI I used the socket extension/steering method of popping out the hub when I went to install the new ones last night I noticed that my axle shaft was starting to come out of the tube, and so I pulled on it gently and ended up pulling the whole thing out.
I'm not sure if doing that caused it, but the axle was out of the tube 1/4" when I went back after turning the wheel. Just something to consider for anyone else thinking of doing this.
So I guess all I need to do to pop open the differential and stick the shaft back in and reattach the c-clip? Am I on the right track here?
I'm not sure if doing that caused it, but the axle was out of the tube 1/4" when I went back after turning the wheel. Just something to consider for anyone else thinking of doing this.
So I guess all I need to do to pop open the differential and stick the shaft back in and reattach the c-clip? Am I on the right track here?
#10
CF Veteran
Join Date: Jul 2009
Location: London Ontario Canada
Posts: 1,254
Likes: 0
Received 10 Likes
on
10 Posts
Year: 2000
Model: Cherokee
Engine: 4.0
No C clip on front axle. don't need it. your bearings keep in place. Just be very careful when you reinsert the axle back as there is an axle seal near the carrier. If you get too agressive, you could damage it.
#11
The extension trick is a great idea. However they make a thing called a hub puller that would of made quick work of this as well. Just fyi for anyone searching about wheel hub bearings.
Good luck with the new ride!
Good luck with the new ride!
#15
CF Veteran
Join Date: Nov 2008
Location: Oak Harbor, WA.
Posts: 6,989
Likes: 0
Received 4 Likes
on
4 Posts
Year: 1987
Model: Cherokee
Engine: 4.0 liter RENIX I-6, DIY Cold Air Intake, 2.5 FM Exhaust, 3 Core Radiator
That 3" extention trick is very cool. What my son and I do is just keep an extra set of the 3 hub bolts in the garage, Whenever we need to remove a hub assembly we simply remove the 3 good bolts and set them aside. We thread the "duty removal bolts" in about 3-5 truns and get out the BFH...lol...and a couple good healthy blows on each of them and the hub assembly pops right out. Remove the "duty" bolts and put them back on the shelf for next time. Just another equally good way of doing the job.