DaRock

Home » Quadratec Knowledge Center »

Jeep Electronic Control Unit Reset

When installing new power or performance accessories how does the computer for the Jeep know that it has a new accessory? Most of the time the computer does not. The computer would need to be reset to take full potential of the performance accessories you have added.

The Electronic Control Module, or ECU as its commonly called, stores the information for your vehicle and your driving habits in its memory. The memory is maintaned by a series of capacitors that hold a charge and maintain power for the ECU when the vehicle is turned off. The following procedure will allow you to reset the memory and allow the computer to 're-learn' how to drive by adjusting to the drivers habits and the vehicles modifications.


1. Disconnect the battery by removing the positive battery cable. Remember, the positive battery cable.

2. Ground the positive cable to the negative cable for 30 seconds to erase the electric charge in the capacitors.

3. Reconnect the positive cable to the battery.

4. Turn the key to on but do not start.

5. Turn the headlights on.

6. Turn the headlights off.

7. Turn the key off.


The ECU has now been reset to its factory settings. For the next 50 warm-up periods the ECU will re-learn the engine and driving habits for your driving conditions and the newly installed parts.

Beer

Or just disconnect the negative battery cable, hold down the brakes for a few seconds, and then reconnect negative battery cable. It does the same thing, the ECU resets itself and for the next 50 warm up periods it will relearn everything.

SRT-10Jeep

How does this work?

gardnern99

I am already averaging about 18.5 mpg in my '91 Cherokee(227,000 miles). I put new plugs/wires in about 5000 miles ago and made an exhaust modification. Is it necessary for me to reset the ECU?

VTJeep

No. You didn't increase the air-fuel-spark ratio, so no need for computer to do anything different. And even if your exhaust is more "free flowing", there is still no increase in intake volume, so nothing really changes except (potentially) back pressure. Which, if you remove too much back pressure without increasing intake volume, your performance will suffer..

KJamesJR

You'll need to see a mechanic or dealer for a "deep reset" however. If this were your average computer... This technique more or less "clears the cache".

I had to do this after installing my CPS. Tried this technique and it just made it run worse.

Gee oh Dee

Kalali

You mean it made run worse than before changing the CPS? Could you elaborate?

DFlintstone

I've seen posted you might just leave it disconnected overnight to "let the capacitors bleed down". No idea myself except it sounds easy and harmless.

Yea^, never heard if trying to clear anything because of the cps....

Kyle Jackson

Can you just use a OTC scan tool to reset or does the capacitors still need drained to relearn? My scan tool has fuel map relearn and cam crank position relearn. That's what I did when I changed my worn out timing chain (https://youtu.be/PfW_StKs3Yw) (about like that lol )and installed cold air intake, 62 mmthrottle body, and magnaflow high flow cat,and the four hole injectors. Have not got readings for mpg yet but it has to be better than 13 mpg. Hoping!

DFlintstone

Hi Kyle and welcome! Not that I could offer anything else regarding your puter', but you do need to fill out your info so we can easily see what you have. (some guys you might want to hear from, might just ignore you if you don't).

If you are running oversize tires your odometer will under read as they are spinning slower. I need to add 4% to my miles before dividing by gallons, for example. The four hole injectors may, or may not give you an extra MPG or two. It WILL idle and run smoother.

Rockchalk

Found this in a search. Is the OP method the best and when I do it do I actually touch the POS terminal to the NEG terminal while the NEG terminal is connected to the battery... or do I disconnect the NEG terminal as well?

Waynerd

I've had success with disconnecting the + cable and resting it on the AC bracket to ground it for a few minutes.

jriveralhn

hi friend, i have a 2015 jeep cherokee sport, this guide works for my cherokee?


best regards!

jriveralhn

Hello, I have a problem, I bought a jeep Cherokee 2015, shocked, at auction, I did not bring the Active Grille Shutter, when I repaired it, showed me the motor check, and when I read the error codes, it shows me the U11E9, reading In several forums that code is for lack of the AGS, I bought it, I wanted to install it but did not recognize it, any idea how to make it recognize it? And can remove that error code.