REAR MAIN SEAL
#1
Junior Member
Thread Starter
Join Date: Jan 2010
Location: CEN-CAL
Posts: 81
Likes: 0
Received 0 Likes
on
0 Posts
Year: 87
Model: Cherokee
Engine: I6
REAR MAIN SEAL
What's up Guys! Hey I got an 87 CherokeeCheif 4.0 I6 with a 5 speed. Does anyone know if I have to pull the tranny to replace the RMS I heard if its a 2 peice you don't if its a single you do but is that only with automatic trans or does the same apply with the manuel?
#2
CF Veteran
Join Date: Aug 2008
Location: Hollidaysburg, PA
Posts: 5,603
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1990
Model: Cherokee
Engine: 4.0 lt. 242 cu.in.
All the 4.0s are 2 piece rear main. You don't have to pull the trans. Just the oil pan and the rear main bearing cap. When you put it back together torque the bearing cap bolts to 80 ft/lbs.
Good Luck!!
Good Luck!!
#3
Junior Member
Thread Starter
Join Date: Jan 2010
Location: CEN-CAL
Posts: 81
Likes: 0
Received 0 Likes
on
0 Posts
Year: 87
Model: Cherokee
Engine: I6
REAR MAIN SEAL
Thanks man! I seem to be having trouble getting that bearing cap off. Is that typical because the Haynes book i'm reading says to take that bearing plate off first before I can pull the oil pan I took the starter off all the bolts out But dosent budge Am I doin somethin wrong let me Know thanks again
#4
CF Veteran
Join Date: Aug 2008
Location: Hollidaysburg, PA
Posts: 5,603
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1990
Model: Cherokee
Engine: 4.0 lt. 242 cu.in.
The oil pan wont budge? Is that what you're saying? I had to use a cold chisel in multiple places on mine, it's a ***** to get off. I ended up getting it to pry away from the block a little bit and then I carefully placed a 2' flathead screwdriver into the hole and pryed the oil pan off. I ended up bending it(that how baked it was onto the block) I just hammered the dent out and put a little extra rtv in that spot.
#6
Junior Member
Thread Starter
Join Date: Jan 2010
Location: CEN-CAL
Posts: 81
Likes: 0
Received 0 Likes
on
0 Posts
Year: 87
Model: Cherokee
Engine: I6
REAR MAIN SEAl
no its not the oil pan that I'm haveing problems with its the plate covers the gears in the very front of the Tranny the book says I need to seperate that before I drop the steerin dapner to pull the oil pan off! Its the plate where you have that peep whole when you pop off the stater off or do I even need to take that off ???? Thanks again for your guys help appericate it!!
#7
CF Veteran
Join Date: Aug 2008
Location: Hollidaysburg, PA
Posts: 5,603
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1990
Model: Cherokee
Engine: 4.0 lt. 242 cu.in.
no its not the oil pan that I'm haveing problems with its the plate covers the gears in the very front of the Tranny the book says I need to seperate that before I drop the steerin dapner to pull the oil pan off! Its the plate where you have that peep whole when you pop off the stater off or do I even need to take that off ???? Thanks again for your guys help appericate it!!
Edit: Maybe for more room to slide the new seal in?
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
MidwestNick
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
10
02-28-2016 02:05 AM
shelby5041
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
39
11-07-2015 01:22 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)