srt-iz

Hey guys, what options came with the Cherokee Country edition? Did these come with skid plates, tow hooks and axle (what size)?

And before i get the smart answer...I know it came with an axle!!

__________________

89' XJ 2D
90' XJ 4D
05' SRT RC
06' Commander

BlueXJ

Go to the Jeep website and you can get the build sheet for your Jeep if you have the serial number and it is 1992 or newer. If like me you have a Renix era Jeep you can ask specific questions and they will respond via e-mail, but no build sheets are available any longer.

__________________

muddeprived

I did this and got my build sheet two days later (2000 tj).

__________________
2001 Sport 4.0 30/8.25 Flux Capacitor Heat Machine
Black XJ club member #1

BlueXJ

About 5 years ago I got mine for my 90 XJ but each year they go forward they drop off a year of the older stuff. So now they go back to 92 and next year it will be 93 and so on ....
Blue

__________________

nick_n_ii

This might help some...
http://offroadjeepers.com/showthread.php?t=583

Cherokee Stock Specs
Common Design

All XJs were built as a "Unibody" design with the body and frame rails tied together as one piece as opposed to a body on frame design. All XJs have solid axles front and rear. The suspension is coils/leaf springs. All XJs came with disc/drums brakes.

Dimensions

(small differences may occur depending on optional equipment or trim level)

wheelbase = 101.4"
overall length = 165.3" - 168.8"
overall width = 67.9" - 70.5"
track = 58"
height = 64"
height with roof rack = 66.8"
ground clearance (from differentials) = 7.3" - 8.3"
approach angle = 37.6* - 38*
departure angle = 31* - 32.1*
breakover angle = 21* - 21.9*
curb weight 2wd = 2,891 lbs - 2,993 lbs
curb weight 4wd = 3,057 lbs - 3,386 lbs
cargo capacity = 71.0 cu ft.

Body

The body comes in both 2-door and 4-door styles with a rear hatch (liftgate).

In 94 side-impact beams were added in the doors and roof was strengthened. The 3rd brakelight was added to the top of the liftgate.

In 96 the body structure was strengthened some although it was not noticeable in appearance.

In 97 the body (and interior) was redesigned to freshen it up a bit. Most noticeably it gave the body smoother lines by changing the bumpers, flares, and moldings. The front fender was trimmed just below the headlights and replaced with plastic bumper endcaps that wrap around to the wheel well. The liftgate was also changed from fiberglass to sheet metal in this year. The windshield washer bottle was also moved to the inside of the drivers side front fender.

Engines

2.5L I4 carburated - 105 hp @ 5000 rpm, 132 ft lb torque @ 2800 rpm - used in 84-85 models
2.5L I4 TBI (fuel injected) - 117 hp @ 5000 rpm, 135 ftlb @ 3500 rpm - used in 86 and updated in 87-90 to 121hp
2.5L I4 MPI (multi-port injection) - 130 hp @ 5250 rpm, 139 ft lb @ 3250 rpm - used in 91-00

GM 2.8L V6 - 115 hp @ 4800 rpm, 145 ft lb @ 2400 rpm - used in 84-86

Renault 2.1L 4cyl. Turbo Diesel - 85 hp @ 3750 rpm, 132 ft lb @ 2750 rpm - used in 85-87

Italian VM 2.5L Turbo Diesel - 140 hp, 236 ft lb torque - used in overseas XJs

4.0L I6 EFI "Power Tech" - 177 hp @ 4750 rpm, 220 ft lb @ 4000 rpm - used 87-90
4.0L I6 MPI "Power Tech HO" (High Output) - 190 hp @ 4750 rpm, 220 ft lb @ 4,000 rpm - used in 91-95 and updated in 96-01 to 225 ft lb torque @ 3000 rpm (00-01 models use a distributorless ignition system)

Transmissions

Manual Transmissions
AX4 - 4 speed manual - manufactured by Aisin - used 84-86 with 2.5L I4 and 2.8L V6 engines
T4 & T5 - 4 & 5 speed manual - manufactured by Borg Warner - used 84-86 with 2.5L I4 and 2.8L V6 engines
BA10/5 - 5 speed manual - manufactured by Peugot - used only up to 89
AX5 - 5 speed manual - manufactured by Aisin - used with 2.8L V6 and 87+ with 2.5L I4
AX15 - 5 speed manual - manufactured by Aisin - used with 4.0L I6 engines
NV3550 - 5 speed manual - manufactured by New Venture - used in 00-01 in SE models with 4.0L I6 engines

Automatic Transmissions
Torqueflight 904 - 3 speed automatic - used 84-86 with 2.8L V6 and 2.5L I4 engines
30RH - 3 speed automatic - used with 2.5L I4 engine 94?-00
AW4 - 4 speed automatic, electronically controlled - manufactured by Aisin - used from 87-01 (87-91 models include a Power/Comfort button that adjusts the shift points)

Transfer Cases

The transfer cases used are all chain driven with aluminum housings. NP stands for "New Process" which is the brand, if you will. The newer ones are NV instead which stands for "New Venture". It is the same transfer case just a different name.

NP207 - "Command-Trac" part-time only - 2.61:1 ratio low range - used 84-87
NP231 - "Command-Trac" part-time only - 2.72:1 ratio low range - shift pattern 2H - 4H - N - 4L - used 87-01

NP228/NP229 - "Selec-Trac" - 4Hi(full-time) - N - 4Lo (part-time) - used 84-87
NP242 - "Selec-Trac" part-time OR full-time - 2.72:1 ratio low range - shift pattern 2wd - 4part-time - 4full-time - N - 4LO - used 87-01

Driveshafts

Front Driveshaft - On 84-87 XJs (NP207 t-case) the front shaft is a "GKN" style shaft. On 87-01 XJs (NP231/242 t-case) the front is a "double cardan" two-piece driveshaft with a CV joint at the transfer case end.

Rear Driveshaft - The rear is a one-piece shaft with standard u-joints at both ends. The slip yoke is located on the output shaft of the transfer case. On 84-95 models, the yoke slides in and out of the transfer case and is lubricated by the ATF fluid internally. On 96-01 due to a design change, the slip yoke is external (does not slide in and out of the transfer case). This slip yoke is covered with a rubber boot.

Axles

Front Axles
Dana 30 high pinion - reverse cut - 27 spline, 1.16" diameter shafts, 7.13" ring gear - used 84-99 (some axles through 91 are vacuum disconnect, 92+ are non-disconnect, 89-95 with ABS have 5-297x u-joints, all 95+ have 5-297x u-joints, all others have 5-260x u-joints)

Dana 30 low pinion - standard cut - 27 spline, 1.16" diameter shafts, 7.13" ring gear, 5-297x u-joints - used 00-01

Rear Axles
(Note on Dana 35 axles sometimes referred to as Dana 35C - The "C" does not stand for c-clip. It stands for "custom" meaning it came from Dana unfinished.)
(Note on 8.25 axles - none of these axles were used on XJs with ABS brakes. If you have ABS, you have the Dana 35. Without ABS you could have either axle. 8.25 axles are c-clip)

Dana 35 non c-clip - 27 spline, 1.18" diameter shafts, 7.58" ring gear, 2.62" axle tube - used 84-89
Dana 35 c-clip - 27 spline, 1.18" diameter shafts, 7.58" ring gear, 2.62" axle tube - used 90-01
Chrysler 8.25 - 27 spline, 1.17" diameter shafts, 8.25" ring gear, 3" axle tube - used 91-96
Chrysler 8.25 - 29 spline, 1.21" diameter shafts, 8.25" ring gear, 3" axle tube - used 97-01
Dana 44 non c-clip - 30 spline, 1.31" diameter shafts, 8.5" ring gear, 2.75" axle tube - used 87-89 on some (not all) XJs equipped with towing package.


Gearing

3.07 - used with 4.0L engine / manual transmission
3.31 - only available on older (pre87?) 2 door XJs with "Fuel Economy" package
3.55 - used with 4.0L engine / automatic transmission
3.73 - found in some XJs with the towing package
4.10 - used with 2.5L engine usually, and older XJs with the "Off-Highway Vehicle" package.
4.56 - rare but can be found on some older (~ 89 ~) models with 2.5L engine and auto transmission

Cooling Systems

Open style - any normal cooling system used today. Opposite of closed style described below.

Closed style - has no radiator cap and utilizes a pressure bottle. This style cooling system was used in 87-90 XJs.

Airbags

Drivers side airbag (mechanical) was added in 95.
Passenger side airbag was added in 97. Airbags changed from mechanical to electronic in this year also.


Production Numbers

# of XJs built in given year:

84 - 93,326
85 - 120,328
86 - 107,225
87 - 139,295
88 - 187,136
89 - 207,216
90 - 151,230
91 - 151,578
92 - 137,826
93 - 144,961
94 - 123,391
95 - 120,234
96 - 286,463
97 - 258,958
98 - 182,845
99 - 186,116
00 - 165,590 (Freedom Edition - 2,821)
01 - 120,454

Total = 2,884,172

Trim Levels

84 - Base, Wagoneer, Pioneer, Chief
85 - Base, Wagoneer, Pioneer, Chief, Laredo
86 - Base, Wagoneer, Pioneer, Chief, Laredo
87 - Base, Wagoneer, Pioneer, Chief, Laredo, Limited
88 - Base, Wagoneer, Pioneer, Chief, Laredo, Limited, Sport
89 - Base, Wagoneer, Pioneer, Chief, Laredo, Limited, Sport
90 - Base, Wagoneer, Pioneer, Chief, Laredo, Limited, Sport
91 - Base, Briarwood, Chief, Laredo, Limited, Sport
92 - Base, Briarwood, Chief, Laredo, Limited, Sport
93 - Base, Sport, Country
94 - SE, Sport, Country
95 - SE, Sport, Country
96 - SE, Sport, Country, Classic
97 - SE, Sport, Country
98 - SE, Sport, Classic, Limited
99 - SE, Sport, Classic, Limited
00 - SE, Sport, Classic, Limited, Freedom
01 - Sport, Limited, 60th Anniversary Edition

__________________

dabeast727

i found somehting very odd about htat...
"Rear Axles
(Note on Dana 35 axles sometimes referred to as Dana 35C - The "C" does not stand for c-clip. It stands for "custom" meaning it came from Dana unfinished.)
(Note on 8.25 axles - none of these axles were used on XJs with ABS brakes. If you have ABS, you have the Dana 35. Without ABS you could have either axle. 8.25 axles are c-clip)"

I have a 8.25, and ive slammed on my brakes before i dont have ABS, or at least its not working. but when i start my engine there is an ABS light that comes on...but according to this all XJs with ABS had d35s....

__________________
1999 cherokee, white, 2 dr, manual, 95k miles
-4.5" Rubicon Express superflex with full packs, plus 1.5" spacers in the front to level out winch/bumper
-32" BFG MTs
-15" black steelies
-ARB snorkel
-TNT winch bumper
-Armor: eng./t-case skid plates, differential shield, TNT bumper w/ cross member skid.
-T-MAX 9,000lb winch
-Dana 30HP front, Crystler 8.25 rear (29 spline)
-Stock gears, 3.07
-4 5.5" roof lights

Plans:
35" BFG AT
4.56
5.5" RE springs & 1" shackles

nick_n_ii

Most all ABS is for the front on Jeeps from what I've seen not all wheels. And there could be a few things missing from the list but it is the most complete I've ever seen for XJ general info..

__________________

Kyle

The abs dummy light was installed on all cherokees.

srt-iz

Ok so i found this junk yard that has like 5 cherokees one of them being a country edition. I think ima go and see if i can get some skids off of this thing. Also they are asking 250 for the axle. Is it worthi it? I think its a 8.25

Is ABS not good? I have ABS all the way around.

__________________

89' XJ 2D
90' XJ 4D
05' SRT RC
06' Commander

BlueXJ

If you decide to get that 8.25 from J/Y then check the gearing,. If it does not match yours then one end or the other will need to be re-geared as well. Just my two cents worth.
Blue

__________________

Kyle

Look on craigslist you can find one for around 125 if you look hard enough, and make sure you get a 97+ 8.25 as it has the 29 spl axles.

XJ Stryker

Also I don't think 250 is a good price for a 8.25. My bud just pulled a D-44 out of our JY for 175. And they even pulled it and loaded it up for him. They wanted 150 if he did the work pulling it he 25 bucks and they will pull it go ahead.

__________________
1987 Black Jeep Wagoneer 4.0L I6 242 30/44 3in RC
1987 Tan Jeep Wagoneer 4.0L I6 242 30/44 3in RC
2006 F-150 King Ranch 5.4L V-8 Triton

Check out my Waggy build here!

TrueBlueXJ

Yeah, 250 isn't a good price for an 8.25. For that you could get an 8.8 or a D44. Heck, you could probably get an 8.8 already set up for an XJ.

__________________
1996 2-door 2.5L, 3.5" RE Superflex, extended LCAs, Gen-2 quick discos, 31" TrXus MTs, Soft 8s, Dynomax exhaust, K&N filter, TB spacer and a never ending wish list.

[_]||||||||[_]

www.jeepinwv.com | www.myspace.com/marvelandmayhem