Bleeding brakes solo
#1
Seasoned Member
Thread Starter
Join Date: Feb 2010
Location: Pharr, Texas
Posts: 272
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1989
Model: Cherokee
Engine: 4.0L
Bleeding brakes solo
If I dont have anyone to help me bleed my brakes how can it be done by one person? If I open all the valves so that brake fluid drips out constantly will this bleed my brakes?
#2
All you need is a piece of rubber tubeing long enough to go from your bleeder valve into a clean soda bottle with a hole in the top to put the hose through and brake fluid of course ! Start out by putting about an inch
of brake fluid in the soda bottle that keeps it from sucking air back into the brake line.Open your bleeder valve and slip the tubeing over it and into the soda bottle make sure the end is in the brake fluid and pump your brake 4-5 times and check your fluid levle in your master cylinder so you dont run out. DON"T reuse what will be in the soda bottle it could be contamimated ! Do it a couple of times on each line make sure to close the bleeder vale and you should be OK.
of brake fluid in the soda bottle that keeps it from sucking air back into the brake line.Open your bleeder valve and slip the tubeing over it and into the soda bottle make sure the end is in the brake fluid and pump your brake 4-5 times and check your fluid levle in your master cylinder so you dont run out. DON"T reuse what will be in the soda bottle it could be contamimated ! Do it a couple of times on each line make sure to close the bleeder vale and you should be OK.
The following users liked this post:
Flagdad (03-11-2020)
#5
Senior Member
I've got a set of Easy Bleeders on mine, they have a one way valve in them to let fluid out but no air in!!! So all you do is loosen all of them and pump away! I **** you not, they're the cat's a$$!!!!!!!!!
#6
I would gravity bleed them like superj says it won't take 4 hours.
1. set up 4 catch pans get twice as much brake fluid as you think you will need.
2.Remove the fluid reservoir cap and fill it. Open and unscrew all the bleeders starting farthest from the fluid reservoir(RR) working your way to (LF).
3. Once they are open they will drip slow clean your bleeders screws with brake clean. Make sure to keep the resivoir full if it goes dry you will need someone to help bleed and possible power bleed.
4. once the fluid appears clean (at this point it will be flowing in a stream) close the bleeders starting at the (RR) working your way back to the (LF)
Fyi if you have seized bleeders you can try and heat them and pound the caliper housing. you can also bleed by cracking the brake lines going into the caliper or brake cylinder in a pinch
1. set up 4 catch pans get twice as much brake fluid as you think you will need.
2.Remove the fluid reservoir cap and fill it. Open and unscrew all the bleeders starting farthest from the fluid reservoir(RR) working your way to (LF).
3. Once they are open they will drip slow clean your bleeders screws with brake clean. Make sure to keep the resivoir full if it goes dry you will need someone to help bleed and possible power bleed.
4. once the fluid appears clean (at this point it will be flowing in a stream) close the bleeders starting at the (RR) working your way back to the (LF)
Fyi if you have seized bleeders you can try and heat them and pound the caliper housing. you can also bleed by cracking the brake lines going into the caliper or brake cylinder in a pinch
Trending Topics
#8
I'm building a DIY pressure bleeder. I started picking up parts today. So far im $10 in.
http://faculty.ccp.edu/faculty/dreed...eder/index.htm
http://faculty.ccp.edu/faculty/dreed...eder/index.htm
#9
Junior Member
Join Date: Nov 2009
Location: apa
Posts: 83
Likes: 0
Received 1 Like
on
1 Post
Year: 2000
Model: Cherokee
Engine: 4.0
The gravity method works fine and took me less than an hour. Cost- one empty windshield washer bottle (going in the trash anyway) some clear tubing, and about four beers (one for each wheel).
#14
Member
Join Date: Feb 2010
Location: Schererville, IN
Posts: 219
Likes: 0
Received 1 Like
on
1 Post
Year: 1997
Model: Cherokee
Engine: 4.0
no, it is not a Cherokee engine, I took that pic from Pelican parts website.. but as long as your cap is the screw-type like the pic, then the power bleeder is the best option from solo bleeding.
#15
I just did it with gravity, it was no trouble at all, I just pressed a clear tube onto the bleeder, loosened it, and it flowed right out. It only took about 5 minutes per wheel max, the setup time was the bulk of it, pumping the brakes wouldn't have made it any easier.